Getting Familiar with Plumbing: The First Step for Bathtub Installation
Getting Familiar with Plumbing: The First Step for Bathtub Installation
Blog Article
The content listed below on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is exceptionally remarkable. Read it for yourself and figure out what you think about it.
Mounting a bath tub isn't precisely brain surgery, however it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is also a moderately hard project. If the old bathtub is conveniently accessible, the job can move immediately; if you need to open a wall surface to get rid of the old bathtub as well as position the new bathtub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will need an assistant to vacate the old tub and set in the new one. Make sure you have actually qualified on your own for the work as well as fit attempting it. Instead of employing a service provider to take over a halfway-completed task, it is much better to think about employing one before you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will certainly aid you set up a brand-new bathtub in your shower room if you have actually currently gotten a new tub and also do not require to alter the setup of your previous supply of water pipes.
Your devices as well as product list need to make up the following:
Preparing for the Installation
Firstly, the supporting frame provided with the bath should be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to ensure that if the tap includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you use all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its last setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, after that the first thing you must do is separate the water. After doing so, switch on the taps to drain pipes any type of water staying in the system. The procedure of removing the existing taps can be rather problematic due to the limited accessibility that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the remaining water that will come from the pipes. Once the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Before carrying on to fit the brand-new taps, compare the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bath tub
Utilizing both wood boards under its feet, put the tub in the needed setting. The wood boards are handy in evenly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four little points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the level checks out level.
To set up taps, fit all-time low of the furthest flexible tap adapter to the proper supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the water system and also examine all joints as well as brand-new pipework for leakages as well as tighten them if needed. Load the tub as well as additionally check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the bathtub must wait up until the bathtub has been utilized at least when as this will resolve it into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipes.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in place in between the faucet and also the sink. Secure the faucet in position with the supplier provided backnut. Once the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet adapters. The previous kind should be linked to the tap ends initially, tightening just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to crack an inflexible seal, creating the water to penetrate the wall surface between the bathroom as well as the tiling, causing difficulties with wetness and feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes and also cartridges, as well as are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to always fill up the bathtub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealant can split rather very early if you do not take into account this motion prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently available on the marketplace. It is recommended to fit the ceramic tiles using waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very inquisitive about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you liked the blog entry. Enjoyed our write-up? Please share it. Let others discover it. Thanks for your time. Don't hesitate to come visit our site back soon.
Expert plumbing diagnostics and repair. Report this page